Search found 1412 matches
- Sun Jun 02, 2024 11:50 am
- Forum: Brakes, Suspension, Steering & Tires
- Topic: 710M vs Garage Height
- Replies: 17
- Views: 679
Re: 710M vs Garage Height
Just one last posting on this from me in case there's an idea that might help. Fortunately for me, my garage is an outside building, with no second floor above. So I had a bit more flexibility to raise the header. It was framed for a standard 6' 6" opening with a flapper type door -- which made...
- Sun Jun 02, 2024 11:08 am
- Forum: Engine
- Topic: Switch key off for engine braking?
- Replies: 2
- Views: 130
Re: Switch key off for engine braking?
I assume what you are describing is post ignition not back firing -- Exhaust "farts" :wink: That can be caused by a very lean condition. Lean under a high vacuum requires more advance as the fuel burns much slower under that condition then results in unburnt fuel in the exhaust. Why this h...
- Tue May 28, 2024 8:43 am
- Forum: Brakes, Suspension, Steering & Tires
- Topic: 710M vs Garage Height
- Replies: 17
- Views: 679
Re: 710M vs Garage Height
Jeffn, One last comment... If you have the bug for a Pinz -- get one. Don't let the garage situation be the show stopper. There are much bigger things to think through such as maintenance, repair, the general condition of one you may acquire AND what your intended use will be -- they ain't the best ...
- Mon May 27, 2024 6:25 pm
- Forum: Brakes, Suspension, Steering & Tires
- Topic: 710M vs Garage Height
- Replies: 17
- Views: 679
Re: 710M vs Garage Height
7' 2" was for my 712M, and only has a low profile antenna mount on the roof. But...there's a lot of variables to consider in that height measurement. Tire size (I have 33"), condition of the Suspension (mine, relatively in good stiff condition), and the odd duck, I backed into the garage. ...
- Mon May 27, 2024 1:51 pm
- Forum: Brakes, Suspension, Steering & Tires
- Topic: 710M vs Garage Height
- Replies: 17
- Views: 679
Re: 710M vs Garage Height
Some models are higher than others. The K's have a roof hatch on the hard top, going to be approximately 7' 6'", if there is an Antenna base mounted would be more vs base type -- but they can be removed. A "M"with a canvas top (no roof hatch) are about 7' 2". I have one of each a...
- Mon May 27, 2024 9:00 am
- Forum: Brakes, Suspension, Steering & Tires
- Topic: 710M vs Garage Height
- Replies: 17
- Views: 679
Re: 710M vs Garage Height
You have PLENTY of headroom -- some will be envious
A 710K with antenna mounts and 33's will be under 8' height.
A 710K with antenna mounts and 33's will be under 8' height.
- Mon May 20, 2024 11:07 pm
- Forum: Engine
- Topic: Hard starting hot
- Replies: 10
- Views: 6417
Re: Hard starting hot
Yes, that is correct!
- Sat May 18, 2024 8:45 am
- Forum: Engine
- Topic: Hard starting hot
- Replies: 10
- Views: 6417
Re: Hard starting hot
JimmyC... What you are describing may be heat soak into the intake manifold. I have experienced this first hand on my Carb'd 712. It is more prevalent if the intake manifolds are not insulated. Styer-Puch had a hot climate version of the Pinz and one thing that was done was to insulate the intake to...
- Wed May 15, 2024 9:20 am
- Forum: Engine
- Topic: Megasquirt MS3Pro Mini ECU
- Replies: 4
- Views: 433
Re: Megasquirt MS3Pro Mini ECU
Curious.... Where did you install the O2 sensor?
- Wed May 15, 2024 9:17 am
- Forum: Electrical
- Topic: Battery going dead
- Replies: 10
- Views: 2828
Re: Battery going dead
I've had this Molex hand crimper for years, never has failed me and works for other "similar" type barrel terminals. Expensive but don't settle for a knockoffs. Amazon link below, you can search for better prices out of places like Digikey etc. P/N 63811-1000 https://www.amazon.com/Molex-6...
- Wed May 15, 2024 9:08 am
- Forum: Engine
- Topic: crankcase ventilation
- Replies: 19
- Views: 3259
Re: crankcase ventilation
For years my EFI 710 ran with no Crank ventilation, like a 50's era car vented to the atmosphere. Couple of years ago after I did a top end rebuild, I decided to be nicer to the environment and correct that and connect to the vacuum vent side of the throttle body -but- I also decided to add a Oil ca...
- Tue Apr 30, 2024 9:47 pm
- Forum: Electrical
- Topic: Power Port Connection
- Replies: 6
- Views: 439
- Mon Apr 29, 2024 8:58 pm
- Forum: Electrical
- Topic: Battery going dead
- Replies: 10
- Views: 2828
Re: Battery going dead
If you remove the top front "tin" which is forward of the Front Carb, that will
give you acess to the back side of the alternator and the Molex connector.
You do NOT have to pull the carbs.
give you acess to the back side of the alternator and the Molex connector.
You do NOT have to pull the carbs.
- Wed Apr 24, 2024 9:32 am
- Forum: Body & Interior
- Topic: Shovel Mounting
- Replies: 2
- Views: 317
Re: Shovel Mounting
Thanks !!!
ron
ron
- Tue Apr 23, 2024 2:50 pm
- Forum: Body & Interior
- Topic: Shovel Mounting
- Replies: 2
- Views: 317
Shovel Mounting
A Swiss shovel has been laying around and I want to mount in my 710K Wheel Well. The Mount for the Blade is present. I have a Handle mount to attach but not sure where the heck it should go. If anyone happens to have their Phone and Head in your 710 Drivers side Wheel Well can you take a PIX of the ...