THE PORTAL HUB - Pinzgauers, Haflingers, Volvo 303s and more!

Holy poop Vince, I got it wrong... The way it is now is 1, 2, 5, 6 , 3, 4, 6 cor and it should be 1, 2, 3, 4, 5, 6 cor So please remove the old section 6 and replace it with 6 cor (corrected) and re-arrange 3 & 4 to come after 1 and 2. Really sorry for the trouble... Best regards and many thanks...

Hi Vince, Thanks for merging all my 6 episodes into one technical article, however I hope you would not mind rearranging section 3 & 4 to go before 5 & 6. Right now it goes 1, 2, 5, 6 , 3, 4... Thanks for the trouble and sorry for the trouble. I also 're-discovered' the tech section again......

Well Gents, the job is done !!! It went all OK, the Pinz is running and shifting gears and took lots of pictures. I would like to make a "Technical Article" like Sound Control by Vince, so I'll start a new 'reply' in this index and see if it meets the required standard. Thanks all for thei...

Thanks Jimm,

Reading it like this it seems simple and possible. I will report on my progress, once I receive the clutch alignment tool.
Thanks again for explaining it to me so clearly.

Best regards,

Jules

Just rechecked the SAV one: SAV2725 = $9.50. Probably would have been a better choice, but they are pretty expensive mailing things to Holland ($40 or more) I have bought lots of stuff there, because either it was too expensive in europe (www.puch.at) or just plain not available. Alas, c'est la vie ...

I just ordered one GM10 spline from Ebay $6.95 ( http://www.ebay.com/itm/New-Clutch-Alignment-Tool-GM10-1-1-8-10-Teeth-GMC-Chevrolet-Pontiac-/262723454853?hash=item3d2b89c785:g:5n8AAOSwcLxYLh-V&vxp=mtr ), mind you, it cost $25 to send it to Holland, where I absolutely could not find one, tried a...

Hi Undysworld,

Great ! thanks a lot, I'll be roving for a clutch alignment tool first...
Thanks for all the info, great help !

Best regards,

Jules

Just another point... I just read in Pinzgauer technical old (july 16, 2006) at 'Clutch problem: M. Wehrman : "When I replaced the clutch in my K I used the pilot tool that came with the Auto-zone kit,only thing I had to do is wrap the end with a few turns of aluminum tape to match the Pinz pil...

Hi Undysworld, You wrote " Do you own the service manuals? If not, we can give you info on pulling it out. ". Well I have the pdf of the the 'Pinzgauer Repair manual for models 710 and 712' (343 pages), that I downloaded a long time ago from "Swiss All-Terrain" at "swissATV....

In the first place, thanks all you guys for answering my post. I realise that there were earlier posts, but it needs the right combination of words to get to the good relevant posts (ie clutch+stuck, clutch+replacement) and when you're panicking about big jobs coming up and all the expected problems...

Unfortunately it did not work; driving in 4th gear and with the clutch fully pressed in, I braked as hard as I could. This turned the engine off, but nothing else, tried 4 times and gave up. Checked the clutch reservoir, but is full. At the clutch-brake box I could see the lever, that moves when you...

Hi Ed, No; I have not stabbed the brake with the clutch pressed in, will try that after I finish this. I have never had a problem with clutch fluid, but will check also. How do I know if the clutch-slave is engaged ? The repair manual is tight on details, but it looks as if I need to remove the cove...

No did not work in 4 thgear, though I managed to drive it in 4th gear, but clutch would not budge. With the clutch fully pressed in, it still did not free it and only behaved as if the clutch was released by my foot. Oh my what is coming at me ? It is a half hour drive, through several villages and ...

I just re-read the previous comments, but did not try it in 4th gear...

I even managed to park her in rear-gear in the garage...
I will go now and try that 4-th gear!

Jules

Well fellow Pinz lovers, it did not work... tried today I managed to get it running in first gear, but no matter how much I pumped the clutch; it would not budge and it is still stuck ... Oh poop, it must be rusted solid. I tried in 1st and 2nd gear; start, then it jumps forward and then runs relati...