Search found 1703 matches
- Tue Sep 19, 2006 2:12 pm
- Forum: Off-Road Events and Trail reports
- Topic: Calico Mogfest '06
- Replies: 59
- Views: 35401
- Fri Sep 15, 2006 7:12 pm
- Forum: Pinzgauer technical (old)
- Topic: broken engine mount studs...
- Replies: 9
- Views: 4658
When you unbolt the mount from the lower crossmember and lift the engine an inch, all will be revealed :wink: It is wise to loosen the other mount bolt(or remove it) to prevent over stress when lifting the engine :shock: Denis told me about the come a long method a couple years back, the roll bar ma...
- Fri Sep 15, 2006 9:56 am
- Forum: Pinzgauer technical (old)
- Topic: broken engine mount studs...
- Replies: 9
- Views: 4658
Ok here is a way to begin, pull the engine cover, take the cap off of the antena mount on the cab, then support the engine with a come along . Remove the mount bracket, and then drill out the broken studs or mig weld a nut to each broken stud and use a wrench to remove the remains :wink: you can the...
- Fri Sep 15, 2006 12:14 am
- Forum: General chat
- Topic: Bad break for H3
- Replies: 45
- Views: 18422
- Tue Sep 12, 2006 10:24 am
- Forum: Pinzgauer technical (old)
- Topic: new bad gear noise
- Replies: 3
- Views: 1804
- Mon Sep 11, 2006 1:14 pm
- Forum: Pinzgauer technical (old)
- Topic: Warm Restart
- Replies: 12
- Views: 5694
One overlooked item is the wire from the distributor to the coil(-), if the terminal end corrodes you will get a loss of spark. I have fixed a few hard/no starts by cleaning the contacts :wink: Get a float level guage to check the carbs, check the shutoff solonoids, then make sure you have a good sp...
- Mon Sep 11, 2006 12:27 pm
- Forum: General chat
- Topic: Plug for spotlight
- Replies: 9
- Views: 3212
- Mon Sep 11, 2006 1:24 am
- Forum: General chat
- Topic: logging on
- Replies: 11
- Views: 5123
- Fri Sep 08, 2006 12:24 am
- Forum: Pinzgauer technical (old)
- Topic: Air Conditioning w/ engine driven compressor
- Replies: 5
- Views: 2848
Well, here is an affordable idea for you, not only will it work, it is cost effective. Make it like my trigger wheel and instead of teeth, have a ring of alluminum or steel cut to form an extention to the rear of the crank pulley, machine the belt groove into the ring and then align and drill , tap ...
- Thu Sep 07, 2006 12:56 pm
- Forum: Pinzgauer technical (old)
- Topic: Power
- Replies: 10
- Views: 4061
I suggest you go drive a Pinz if you are interested in one or you will be wasting your time and money. A good running Pinz (710M )will do 65mph(fast enough for an overglorified tractor) :roll: As far as what the driveline will take, I wouldn't push much past 125hp . If you take the time to search th...
- Tue Sep 05, 2006 6:56 pm
- Forum: General chat
- Topic: Lost Posts Again?
- Replies: 4
- Views: 2720
- Tue Aug 08, 2006 1:33 am
- Forum: Pinzgauer technical (old)
- Topic: Towing capacity?
- Replies: 39
- Views: 23542
You wire the controller directly to the rear battery for 12 volt source. It's the 12v signal wire(trigger)that is a bit tricky, I put 2 12v LED bulbs in line to cut the 24v brake sense/trigger wire to 12v. It's really a no brainer :roll: The blue and white wires from the controller then get hooked t...
- Tue Aug 01, 2006 4:50 pm
- Forum: Pinzgauer technical (old)
- Topic: Towing capacity?
- Replies: 39
- Views: 23542
Guys, my truck did not roll , it went over on it's rt side.(the trailer rolled) I was pulling a 710M on my car trailer behind my 710M at 46 mph when it happened. I contribute the mis-hap to small errors that added up . 1 the load should have been a few inches further forward, 2 the weight distributi...
- Wed Jul 26, 2006 7:09 pm
- Forum: Pinzgauer technical (old)
- Topic: Oil Filter cross number for the U.S.
- Replies: 10
- Views: 8690
- Wed Jul 26, 2006 2:07 pm
- Forum: Pinzgauer technical (old)
- Topic: Fuel injection revisited
- Replies: 52
- Views: 32388
The Throttle body is 60mm off a ford 4.6L modular engine(92-95 T bird or Lincoln town car). I'll be getting it to the dyno next week as I have the dreaded jury duty the rest of the week :shock: Hey Jake can you re-post fan balance info and where to send them?, I can't find a mailing address on your ...