Search found 1395 matches
- Tue Dec 19, 2023 8:03 am
- Forum: Owner builds, customizations & accessories
- Topic: Airpod Pro (or other) for phone calls?
- Replies: 4
- Views: 2785
Re: Airpod Pro (or other) for phone calls?
I've been using a Bose noise cancelling headset (with built in Mic). It pairs to two endpoints. In my case a iPhone and a Pryme BT-501. The headset will flip to the iPhone when there is an incoming call. The Pryme dongles are designed to plug directly into a Kenwood or Baofeng hand held. They have a...
- Wed Nov 15, 2023 9:52 pm
- Forum: Engine
- Topic: Oil dripping from pan
- Replies: 2
- Views: 997
Re: Oil dripping from pan
On the drivers side is the cylinder side so there are several possibilities.
But a pix of the area would help.
But a pix of the area would help.
- Sun Nov 05, 2023 7:38 am
- Forum: Engine
- Topic: Lean mixture
- Replies: 4
- Views: 818
Re: Lean mixture
I assume MOT stuck their probe up the exhaust pipe. So any air leak in the exhaust system is also a possibility for a high Lamda reading. Exhaust header, coupler from header to heat-exchanger, lot of parts in that path that might be worn or loose. Then the heat-exchanger itself or muffler. Look for ...
- Tue Oct 31, 2023 8:22 am
- Forum: Engine
- Topic: Lean mixture
- Replies: 4
- Views: 818
Re: Lean mixture
Yikes! That's an AFR = 20.58 mighty lean. And if so, not a healthy condition. If true there are a number of possible things that could result in a high Lamda, possibly a bad vacuum leak. Do you have a high idle? Is it difficult to start or runs rougher than in the past at idle or at RPM? Check all p...
- Mon Oct 30, 2023 8:50 am
- Forum: Electrical
- Topic: Distributor to coil cable assembly?
- Replies: 2
- Views: 812
Re: Distributor to coil cable assembly?
Try Puch.at, they will ship to the USA. A little cumbersome to make the transaction but they are very responsive. https://www.puch.at/en/products-&-spare-parts/pinzgauer/pinzgauer-petrol-710-712-(austrian-army)/electrical-equipment/ignition-system/21116_12616_shop_IGNITION-CABLE-COMPL.aspx?LNG=en
- Thu Oct 12, 2023 9:10 am
- Forum: General chat
- Topic: Project: "Rescue MOG" Follow my new project!
- Replies: 4
- Views: 941
Re: Project: "Rescue MOG" Follow my new project!
Vince, as with all your projects, I'm betting this mog-wrecker is gonna set a new standard -- Matt watch out buddy
Wish I was closer to ya, I'd love to help out.
ron
Wish I was closer to ya, I'd love to help out.
ron
- Thu Sep 28, 2023 9:58 am
- Forum: Engine
- Topic: Vapor Lock
- Replies: 4
- Views: 2098
Re: Vapor Lock
I have little choice but to run E10 gas. It's a matter of practical convince. Almost W/O exception that's what your friendly gas stations sell. I've looked for pure-gas https://www.pure-gas.org/ and the options are spartan. At least I am running summer blend. E10 does bump up the Reid Vapor Pressure...
- Thu Sep 28, 2023 9:36 am
- Forum: Engine
- Topic: Vapor Lock
- Replies: 4
- Views: 2098
Re: Vapor Lock
To answer Vince's question -- idling before turning the motor off might reduce Vapor lock due to heat soak. I say might because it all depends on the circumstances; idle RPM effects air flow, your current elevation, ambient temp, and fuel your using. But, when your on a very steep grade, need to jum...
- Wed Sep 20, 2023 5:51 pm
- Forum: Engine
- Topic: High Water
- Replies: 2
- Views: 623
Re: High Water
I would expect Puch would have done a worse case analysis; truck loaded to max
and a wee bit of additional margin.
Kind'a don't want water hitting the fan or Ignition components.
and a wee bit of additional margin.
Kind'a don't want water hitting the fan or Ignition components.
- Wed Sep 20, 2023 9:36 am
- Forum: Owner builds, customizations & accessories
- Topic: Starter nut
- Replies: 2
- Views: 933
Re: Starter nut
The two Nuts that bolt the starter to the mounting plate are M12-1.75 (8)
- Wed Sep 13, 2023 7:08 pm
- Forum: Owner builds, customizations & accessories
- Topic: New Owner of a 710M. Looking forward to learning a lot!
- Replies: 12
- Views: 1571
Re: New Owner of a 710M. Looking forward to learning a lot!
The engine compartment of a Pinz can get pretty stressful for an electric fuel pump. Ironically worse after you turn the motor off and airflow stops. Some pumps can take a beating, most can't. If your pump is located near where the mechanical pump was I strongly suggest you move it out of the engine...
- Wed Sep 06, 2023 11:49 am
- Forum: General chat
- Topic: Tipping Point
- Replies: 2
- Views: 553
Re: Tipping Point
They can get tippy... Pretty narrow Track at 57" versus a stock JK at 62" for example. Somewhat high center-of-gravity due to relatively high clearance with Portal axles. The K's are more tippy than the M's -- just a bit more weight with more steel above the central tube. Generally, you ju...
- Wed Sep 06, 2023 9:40 am
- Forum: Owner builds, customizations & accessories
- Topic: New Owner of a 710M. Looking forward to learning a lot!
- Replies: 12
- Views: 1571
Re: New Owner of a 710M. Looking forward to learning a lot!
Congrat's on a very nice looking Pinz'y. And welcome to the forum.
- Sat Aug 26, 2023 5:09 pm
- Forum: Engine
- Topic: Vapor Lock
- Replies: 4
- Views: 2098
Vapor Lock
I had an interesting case of Vapor Lock on my Carb'd 712 that initially surprised me. Turned out to be a classic case of heat soak. Some context, I have a Hardi 24V electric fuel pump, located external to the engine about center line of the tank, well within the siphoning limit of this diaphragm pum...
- Fri Aug 11, 2023 4:26 pm
- Forum: Electrical
- Topic: Battery going dead
- Replies: 5
- Views: 1386
Re: Battery going dead
I actually mistakenly referred to DF when I meant D+ !! There are two outputs from the alternator, D+ and B+. B+ is the high current output to charge the battery. D+ on the other hand is monitored by the regulator to control the amount of current on the "DF" the field winding to output mor...