
Another noise thread by a newbie....:)
Re: Another noise thread by a newbie....:)
Well, I was able to remove the drain bolt on the rear diff and I am happy to report there was plenty of fluid in there. Old fluid, but it was there
. Since the drain bolt was not rounded out, but over sized for the 10MM, I was able to tap in an 11MM hex and that worked like a charm. The plug is now shaped to accept the 11MM perfectly. I will change it out when I get my new plugs just to be safe. Now to drive it and see if the noise reappears....so far it hasn't.

Ottawa, Canada
1974 710M
2007 2WD Ural Patrol
1974 710M
2007 2WD Ural Patrol
Re: Another noise thread by a newbie....:)
Just thought I would give my 2 cents, be sure to use anti-sieze on the plugs, with the dissimilar
metals the need that extra protection to prevent galling the aluminium case.
Oh...you only need about 8 ft./lbs torque.
Scott (IE) also sell a new style plug.
Best wishes
metals the need that extra protection to prevent galling the aluminium case.

Oh...you only need about 8 ft./lbs torque.

Scott (IE) also sell a new style plug.
Best wishes
Thomas E.
Sonora, CA
712 Camper
[img][url]M:\avatar\DSCN0010%20(Custom).JPG[/url][/img]
Sonora, CA
712 Camper
[img][url]M:\avatar\DSCN0010%20(Custom).JPG[/url][/img]
Re: Another noise thread by a newbie....:)
To add to this thread, and I am not sure this has any commonality with
berger's thread, but I also have a rather unusual noise, or better -- a
harmonic vibration. At a similar speed to berger, e.g. 90 KPH, there
is a rolling vibration, initially vibration free, then building up to a peak
shaking the rig, this repeats every 4-5 seconds. Yes, I have EX-1's,
but Scott at EI checked these out and in good shape. Brian at EI even
took his tires of his truck and tried them on my, same symptom, so
rim/balance doesn't seem to be a player here. This is just odd at this
frequency of 4 to 5 seconds, and very annoying -- I do like the gear
whining though. I also installed Jim's "Quietizer" on the tranny
mount -- no luck.
P.S. Berger, if your plug thread is stripped, I'd recommend Helicoil, I
used this on my 18mm-1.5mm O2 bung and it worked great -- tight
space on a Pinz header for this operation.
ron
I
berger's thread, but I also have a rather unusual noise, or better -- a
harmonic vibration. At a similar speed to berger, e.g. 90 KPH, there
is a rolling vibration, initially vibration free, then building up to a peak
shaking the rig, this repeats every 4-5 seconds. Yes, I have EX-1's,
but Scott at EI checked these out and in good shape. Brian at EI even
took his tires of his truck and tried them on my, same symptom, so
rim/balance doesn't seem to be a player here. This is just odd at this
frequency of 4 to 5 seconds, and very annoying -- I do like the gear
whining though. I also installed Jim's "Quietizer" on the tranny
mount -- no luck.
P.S. Berger, if your plug thread is stripped, I'd recommend Helicoil, I
used this on my 18mm-1.5mm O2 bung and it worked great -- tight
space on a Pinz header for this operation.
ron
I
Puller: 71' 710K 2.7L EFI aka Mozo
Follower: Sankey MK 3, 3/4 Tonne
Rescue Pinz: 73' 712MK
Driver: Ron // KO0Q
Follower: Sankey MK 3, 3/4 Tonne
Rescue Pinz: 73' 712MK
Driver: Ron // KO0Q
-
- Posts: 1776
- Joined: Fri Apr 16, 2004 8:08 am
- Location: Blue Mounds, WI
Re: Another noise thread by a newbie....:)
Ron,
Yours sounds like maybe an out of balance internal driveshaft. Try engaging the first locker at highway speeds on a straight road. If it goes away when locked, then your driveshaft needs repair.
Yours sounds like maybe an out of balance internal driveshaft. Try engaging the first locker at highway speeds on a straight road. If it goes away when locked, then your driveshaft needs repair.
Re: Another noise thread by a newbie....:)
Thanks, I'll give that a try, although all shafts had been balanced,
but all ideas are very much appreciated!
cheers,
but all ideas are very much appreciated!
cheers,
Puller: 71' 710K 2.7L EFI aka Mozo
Follower: Sankey MK 3, 3/4 Tonne
Rescue Pinz: 73' 712MK
Driver: Ron // KO0Q
Follower: Sankey MK 3, 3/4 Tonne
Rescue Pinz: 73' 712MK
Driver: Ron // KO0Q