EFI installation instructions

Old forum posts ending on Oct 21 '09

Moderator: TechMOGogy

Locked
Jim LaGuardia
United States of America
Posts: 1707
Joined: Wed Apr 14, 2004 3:42 pm
Location: San Bernardino Ca
Contact:

EFI installation instructions

Post by Jim LaGuardia »

I posted the instructions on my website, you can view them at http://204.200.199.239/efiinstallationinstructions.html
Cheers, Jim LaGuardia
http://smg.photobucket.com/albums/v510/Goatwerks/
"Arch Magus of Machines."
Pinz Enthusiast
Posts: 177
Joined: Thu Dec 01, 2005 11:31 pm
Location: Brighton, Co

EFI installation instructions

Post by Pinz Enthusiast »

Jim,

Hard to belive nobody has responded to this, your system is awsome and actualy road tested, I like the fact that it's do able for well under $2000.00 installed and dynoed, and the new map you ran when we went to lunch yeaterday was great, smooth as butter and no fuel smell, the unit is diald in and this is the one everyone should get cause it's actually affordable and has top notch tech support that don't dissapear for months at a time, god knows I could not affort to wait for a tech person to come back from the road to help me, your always available within a few hours notice.....great kit you should sell them out soon.
Eric
Anaheim Hills, Ca
1973 712M
1996 LR Disco I
2003 LR Discovery SE
2003 Holiday Rambler Endeavor MH
hope to get a 1969 Ford M656
andy
Posts: 963
Joined: Thu Feb 15, 2007 6:31 pm
Location: Comstock, TX

Post by andy »

I suspect there are others out there probably alot like me. I'd be interested, but I KNOW I'm not technologically far enough along to attempt something like that on my own. :oops: I'm also about 2 days plus drive from the left coast and the logistics of getting there would be tough to say the least.
Regards,
Andy
A bar F
The buck STARTS here
www.deerleaseservices.com
todds112
Posts: 666
Joined: Sun Dec 03, 2006 5:45 pm
Location: Jackson Hole, WY

Post by todds112 »

Andy wrote:I suspect there are others out there probably alot like me. I'd be interested, but I KNOW I'm not technologically far enough along to attempt something like that on my own. :oops: I'm also about 2 days plus drive from the left coast and the logistics of getting there would be tough to say the least.
Regards,
Andy
Ditto. :cry:
1973 712M
Foz
Posts: 80
Joined: Thu Apr 29, 2004 11:06 pm
Contact:

Post by Foz »

I say we put Jim on tour... maybe we can get some old rock band to open for him? I vote for Ted Nugent.
Foz
PinzEOD
Posts: 277
Joined: Wed Apr 14, 2004 3:45 pm
Location: Las Vegas, NV
Contact:

Post by PinzEOD »

Due to the bubblegum/bailing wire technology of the Pinz, I'd have to vote for Devo.
Mike Newton 1973 712M (sold)
I do not like this word "bomb." It is not a bomb. It is a device that is exploding. Jacques le Blanc
andy
Posts: 963
Joined: Thu Feb 15, 2007 6:31 pm
Location: Comstock, TX

Post by andy »

I wouldn't care if it was The Village People :roll: or all of the above, just put him on tour.

Andy
A bar F
The buck STARTS here
www.deerleaseservices.com
PinzEOD
Posts: 277
Joined: Wed Apr 14, 2004 3:45 pm
Location: Las Vegas, NV
Contact:

Post by PinzEOD »

Perhaps a Pinz maintenance video conference?
Mike Newton 1973 712M (sold)
I do not like this word "bomb." It is not a bomb. It is a device that is exploding. Jacques le Blanc
Locked